机械5

刀盘加工工艺及斜孔车夹具设计 摘要 本设计是基于刀盘零件的加工工艺规程及一些工序的专用夹具设计。刀盘零件的主要加工表面是外圆及孔系。一般来说，保证平面的加工精度要比保证孔系的加工精度容易。因此，本设计遵循先面后孔的原则。并将孔与平面的加工明确划分成粗加工和精加工阶段以保证孔系加工精度。夹具选用专用夹具，夹紧方式多选用手动夹紧，夹紧可靠，机构可以不必自锁。因此生产效率较高。适用于大批量、流水线上加工。能够满足设计要求。 关键词：刀盘类零件；工艺；夹具； ABSTRACT The desig
n is based o
n the body parts of the processi
ng order of the processes a
nd some special fixture desig
n. Body parts of the mai
n pla
ne of the surface a
nd pore system. I
n ge
neral, the pla
ne guara
ntee processi
ng precisio
n tha
n that of holes machi
ni
ng precisio
n easy. Therefore, this desig
n follows the surface after the first hole pri
nciple. Pla
ne with holes a
nd the processi
ng clearly divided i
nto roughi
ng a
nd fi
nishi
ng stages of holes to e
nsure machi
ni
ng accuracy. Datum selectio
n box i
nput shaft a
nd the output shaft of the supporti
ng hole as a rough be
nchmark, with top with two holes as a precisio
n tech
nology refere
nce. Mai
n processes arra
ngeme
nts to support holes for positio
ni
ng a
nd processi
ng the top pla
ne, a
nd the
n the top pla
ne a
nd the supporti
ng hole locatio
n hole processi
ng tech
nology. I
n additio
n to the follow-up processes i
ndividual processes are made of the top pla
ne a
nd tech
nological hole locatio
n hole a
nd pla
ne processi
ng. Supported hole processi
ng usi
ng the method of coordi
nate bori
ng. The whole process of processi
ng machi
ne combi
natio
ns were selected. Selectio
n of special fixture fixture, clampi
ng mea
ns more choice of p
neumatic clampi
ng, clampi
ng reliable, i
nstitutio
ns ca
n
not be locked, so the productio
n efficie
ncy is high, suitable for large batch, li
ne processi
ng, ca
n meet the desig
n requireme
nts. Key words: A
ngle gear seat parts; fixture; 目录 摘要II ABSTRACT III 第1章加工工艺规程设计1 1.1零件的分析1 1.1.1零件的作用1 1.1.2零件的工艺分析1 1.2刀盘加工的主要问题和工艺过程设计所应采取的相应措施1 1.2.1孔和平面的加工顺序2 1.2.2加工方案选择2 1.3刀盘加工定位基准的选择2 1.3.1粗基准的选择2 1.3.2精基准的选择3 1.4刀盘加工主要工序安排3 1.5机械加工余量、工序尺寸及毛坯尺寸的确定5 1.6选择加工设备及刀、量具6 1.7确定切削用量及基本工时（机动时间） 6 第2章车4-φ17孔夹具设计16 2.1车床夹具设计要求说明16 2.2车床夹具的设计要点16 2.3定位机构18 2.4夹紧机构18 2.5零件的车床夹具的加工误差分析19 2.6确定夹具体结构尺寸和总体结构20 2.7零件的车床专用夹具简单使用说明21 结论22 参考文献23 致谢25